{"product_id":"n-013-811-4-genuine-vw-audi-coolant-pipe-drain-plug-sealing-ring","title":"N-013-811-4 Genuine VW\/Audi Coolant Pipe Drain Plug Sealing Ring","description":"\u003ch2\u003eGenuine coolant-pipe drain-plug seal\u003c\/h2\u003e\u003cp\u003eThe N-013-811-4 Genuine VW\/Audi sealing ring serves the specified Touareg coolant-pipe drain-plug connection and the assigned Audi water-pipe sealing joints listed below. One individual ring is supplied.\u003c\/p\u003e\u003cp\u003eThe Touareg entry requires the BAR 4.2L FSI engine. The Audi entries describe separate original water-pipe sealing points within the oil-filter\/cooler arrangement. Match the full factory number and actual joint rather than selecting by approximate ring appearance.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eComplete factory number: N-013-811-4.\u003c\/li\u003e\n\u003cli\u003eNominal catalog size: 10 × 13.5 mm.\u003c\/li\u003e\n\u003cli\u003eType: sealing washer\/ring as shown in the archive photograph.\u003c\/li\u003e\n\u003cli\u003eQuantity supplied: one individual sealing ring.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe catalog size describes the component's nominal opening and outside diameter. It is not a shipping measurement. Match the exact part number and sealing joint; a conventional fastening washer or a similarly sized rubber O-ring does not necessarily provide the required sealing arrangement.\u003c\/p\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe original sealing ring has been disturbed during service of the assigned connection.\u003c\/li\u003e\n\u003cli\u003eThe sealing faces are damaged, scored or visibly deformed.\u003c\/li\u003e\n\u003cli\u003eThe ring is missing or an incorrect substitute was installed previously.\u003c\/li\u003e\n\u003cli\u003eInspection of a leak at the assigned joint identifies damaged sealing hardware.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eInspect the plug or fastener, receiving threads and mating sealing surface before assembly. A new ring cannot repair a cracked component, damaged seat or stripped thread. Confirm the actual source of any leak before replacing parts, and follow the factory replacement requirements for sealing components disturbed during the repair.\u003c\/p\u003e\u003ch3\u003eVehicle fitment\u003c\/h3\u003e\u003cp\u003eMatch the vehicle, engine and assigned sealing point. The Touareg row excludes the earlier AXQ engine, and the Audi rows do not describe a general oil-drain-plug seal.\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eVolkswagen Touareg\u003c\/td\u003e\n\u003ctd\u003e2007–2009\u003c\/td\u003e\n\u003ctd\u003e4.2L BAR FSI gasoline V8\u003c\/td\u003e\n\u003ctd\u003e7L SUV; 4Motion; original front coolant-pipe drain plug; 6-speed automatic\u003c\/td\u003e\n\u003ctd\u003eBAR engine only. Assigned N0160243 M10×1 drain-plug seal at the original coolant pipe. One ring supplied; plug not included.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A8\u003c\/td\u003e\n\u003ctd\u003e2001–2002\u003c\/td\u003e\n\u003ctd\u003e4.2L naturally aspirated gasoline V8\u003c\/td\u003e\n\u003ctd\u003eD2 sedan, quattro, standard wheelbase; 5-speed automatic\u003c\/td\u003e\n\u003ctd\u003eAssigned original water-pipe sealing joint in the oil-filter\/cooler assembly specifying N-013-811-4. Confirm the exact sealing point; not a blanket oil-drain-plug or all coolant-joint fitment.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A8 L\u003c\/td\u003e\n\u003ctd\u003e2001–2002\u003c\/td\u003e\n\u003ctd\u003e4.2L naturally aspirated gasoline V8\u003c\/td\u003e\n\u003ctd\u003eD2 sedan, quattro, long wheelbase; 5-speed automatic\u003c\/td\u003e\n\u003ctd\u003eAssigned original water-pipe sealing joint in the oil-filter\/cooler assembly specifying N-013-811-4. Confirm the exact sealing point; not a blanket oil-drain-plug or all coolant-joint fitment.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi S8\u003c\/td\u003e\n\u003ctd\u003e2001\u003c\/td\u003e\n\u003ctd\u003e4.2L naturally aspirated gasoline V8\u003c\/td\u003e\n\u003ctd\u003eD2 sedan, quattro; 5-speed automatic\u003c\/td\u003e\n\u003ctd\u003eOriginal assigned water-pipe sealing joint within the oil-filter\/cooler arrangement requiring N-013-811-4. Confirm the original complete number and actual sealing location.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch3\u003eInstallation guidance\u003c\/h3\u003e\u003cp\u003eFollow the factory cooling-system drain and refill procedure for the vehicle. Allow the system to cool and release pressure as prescribed before opening the connection. Keep the correct plug and sealing-ring position identified during disassembly.\u003c\/p\u003e\u003cp\u003eClean and inspect the intended sealing surfaces using the prescribed service method. Install the specified ring in the correct original position and engage the associated plug or fastener carefully. Follow the factory tightening instruction for the exact joint rather than using extra torque to compensate for damaged sealing surfaces.\u003c\/p\u003e\u003cp\u003eRefill and bleed the cooling system using the factory procedure, then carry out the specified operating and leak checks at the repaired connection.\u003c\/p\u003e\u003ch3\u003eOrdering information\u003c\/h3\u003e\u003cp\u003eSupplied as one genuine sealing ring. Plug, bolt, pipe, control assembly, fluids and a complete repair kit are not included. Confirm the quantity needed for the specific connection being serviced.\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48046861254833,"sku":"N-013-811-4","price":2.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-013-811-4-genuine-vw-audi-1.jpg?v=1792126712","url":"https:\/\/hstuning.com\/products\/n-013-811-4-genuine-vw-audi-coolant-pipe-drain-plug-sealing-ring","provider":"HS Tuning ","version":"1.0","type":"link"}