{"product_id":"n-106-403-01-genuine-vw-audi-front-subframe-bolt-m12-x-1-5-x-100","title":"Front Subframe Bolt - M12 x 1.5 x 100","description":"\u003cp\u003e\u003cstrong\u003eGenuine VW\/Audi mounting bolt, part number N-106-403-01.\u003c\/strong\u003e This collared hex fastener is used at assigned front subframe mounting positions on the A3 8P and at the rear lateral arm-to-knuckle connection on the A3 quattro configuration below. These are separate mounting applications; select by the original number and exact joint.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOriginal part number: N-106-403-01 \/ N10640301.\u003c\/li\u003e\n\u003cli\u003ePublished nominal size: M12 x 1.5 x 100.\u003c\/li\u003e\n\u003cli\u003eExternal hex head with integral collar beneath the head.\u003c\/li\u003e\n\u003cli\u003eApplications include assigned front subframe attachment and the specified rear lateral arm-to-knuckle joint.\u003c\/li\u003e\n\u003cli\u003eThe cataloged A3 attachment uses two of this original number; this listing supplies one bolt.\u003c\/li\u003e\n\u003cli\u003eSubframe, brackets and other mounting fasteners are separate.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe front subframe supports and locates several chassis components in the vehicle. Correct mounting hardware helps keep the assembly seated in its prescribed position. Several bolt lengths and mounting arrangements can be used across the same subframe, so the original number and exact attachment point are essential selection details.\u003c\/p\u003e\u003cp\u003eThis M12 bolt is not a complete subframe hardware kit. Check every mounting position separately and obtain the additional bolts, brackets or locating hardware required by the repair procedure.\u003c\/p\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cp\u003eReplacement is commonly required when the subframe connection has been released during suspension, steering or drivetrain service and the factory procedure specifies new mounting hardware. Replace damaged threads, a rounded hex head, deformation, missing hardware or corrosion affecting reliable installation.\u003c\/p\u003e\u003cp\u003eEarlier repairs may leave an incorrect substitute bolt or a reused fastener at a position that requires replacement. Inspect the complete attachment arrangement before reinstalling the subframe.\u003c\/p\u003e\u003cp\u003eClunks, steering changes or alignment problems require diagnosis of the suspension, steering and mounting components. A new bolt cannot repair a bent subframe, damaged body mounting point, worn control-arm bushing or defective steering component. Repair those faults and inspect the mating threads and contact surfaces before final assembly.\u003c\/p\u003e\u003ch3\u003eInstallation and service notes\u003c\/h3\u003e\u003cp\u003eFor the rear lateral arm application, use the factory procedure for the exact suspension joint. Replace hardware designated for one-time use, inspect the arm bushing and knuckle mounting surfaces, and observe the specified suspension loading position during final tightening. Subframe tightening values do not apply to this rear arm connection.\u003c\/p\u003e\u003cp\u003eFollow the factory front subframe procedure for the exact vehicle. Support the subframe and any affected powertrain components with the prescribed equipment before releasing mounting bolts. Observe the specified order for disconnecting attached suspension, steering and related components.\u003c\/p\u003e\u003cp\u003ePreserve or establish the prescribed subframe position using the approved locating procedure. Inspect mounting faces and body threads, then install the correct hardware at each assigned position. Start the bolts by hand in undamaged threads rather than using tightening force to pull a misaligned assembly into place.\u003c\/p\u003e\u003cp\u003eFollow the required tightening sequence, torque and additional angle for this exact attachment. Use the specified thread preparation and replace all one-time-use hardware called out by the factory procedure.\u003c\/p\u003e\u003cp\u003eDo not transfer a tightening value from another subframe bolt, engine mount connection or M12 fastener. Different lengths and mounting positions can have different requirements. If a bolt binds or the subframe does not seat normally, inspect component alignment and hardware selection before continuing.\u003c\/p\u003e\u003cp\u003eComplete the prescribed steering, suspension and alignment checks after service. Confirm that all affected components and lines have their required clearance and that the full mounting arrangement is secure. This listing supplies one original bolt; order the quantity needed for the repair.\u003c\/p\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A3\u003c\/td\u003e\n\u003ctd\u003e2006–2008\u003c\/td\u003e\n\u003ctd\u003e2.0L turbocharged FSI gasoline, BPY only\u003c\/td\u003e\n\u003ctd\u003e8P hatchback, front-wheel drive; 6-speed manual\u003c\/td\u003e\n\u003ctd\u003eSpecified front subframe-to-vehicle mounting bolt at the assigned N10640301 positions; two required for the cataloged attachment. Match original number and position; other subframe bolts differ.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A3\u003c\/td\u003e\n\u003ctd\u003e2006–2008\u003c\/td\u003e\n\u003ctd\u003e2.0L turbocharged FSI gasoline, BPY only\u003c\/td\u003e\n\u003ctd\u003e8P hatchback, front-wheel drive; 6-speed DSG\u003c\/td\u003e\n\u003ctd\u003eSpecified front subframe-to-vehicle mounting bolt at the assigned N10640301 positions; two required for the cataloged attachment. Match original number and position; other subframe bolts differ.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A3 quattro\u003c\/td\u003e\n\u003ctd\u003e2015\u003c\/td\u003e\n\u003ctd\u003e2.0L turbocharged gasoline\u003c\/td\u003e\n\u003ctd\u003e8V sedan, quattro; 6-speed S tronic\u003c\/td\u003e\n\u003ctd\u003eOriginal rear lateral arm-to-knuckle bolt N10640301 for the AWD suspension. Match the original number and joint; the FWD knuckle bolt differs. Replace when removed as directed by the factory repair procedure.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003e\u003cem\u003eConfirm the original bolt number and assigned front subframe mounting position before ordering. One bolt supplied.\u003c\/em\u003e\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48007634747569,"sku":"N-106-403-01","price":12.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-106-403-01-genuine-vw-audi-1.jpg?v=1791296488","url":"https:\/\/hstuning.com\/products\/n-106-403-01-genuine-vw-audi-front-subframe-bolt-m12-x-1-5-x-100","provider":"HS Tuning ","version":"1.0","type":"link"}