{"product_id":"n-107-302-01-genuine-vw-audi-turbocharger-outlet-flange-stud","title":"N-107-302-01 Genuine VW\/Audi Turbocharger Outlet Flange Stud","description":"\u003cp\u003e\u003cstrong\u003eGenuine VW\/Audi turbocharger outlet flange stud, part number N-107-302-01.\u003c\/strong\u003e This original threaded stud provides the assigned attachment point for securing the catalytic converter to the turbocharger outlet flange on the configurations below. It is supplied individually for exhaust removal, flange repair or replacement of damaged mounting hardware.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOriginal number: N-107-302-01 \/ N10730201.\u003c\/li\u003e\n\u003cli\u003ePublished nominal size: M10 x 32; published thread pitch: 1.5 mm.\u003c\/li\u003e\n\u003cli\u003eDouble-ended threaded stud with internal drive at the end shown in the original product image.\u003c\/li\u003e\n\u003cli\u003eApplication: assigned turbocharger outlet flange-to-catalytic converter attachment.\u003c\/li\u003e\n\u003cli\u003eOne stud supplied. Mating nut, outlet sealing gasket, turbocharger and converter are separate.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe stud screws into the assigned flange position and provides the threaded attachment for the mating exhaust component. Correct hardware and the specified gasket work together to form the intended outlet connection. The stud itself is not an exhaust seal.\u003c\/p\u003e\u003cp\u003eNearby exhaust joints can use different studs, nuts or bolts. Select this part by original number and actual flange position, rather than assuming that every turbocharger outlet uses the same M10 hardware.\u003c\/p\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cp\u003eReplacement may be needed when exhaust disassembly reveals damaged threads, a broken stud, deformation or corrosion that prevents reliable attachment. Renew hardware wherever the factory procedure requires replacement after removal.\u003c\/p\u003e\u003cp\u003eHeat cycling and earlier repair work can make outlet fasteners difficult to remove or leave damaged threads in the stud or flange. Inspect the complete mounting connection before fitting a new stud.\u003c\/p\u003e\u003cp\u003eExhaust noise, leakage or a loose outlet connection requires diagnosis of the flange, gasket, mating component and support hardware. A new stud cannot repair a cracked flange, damaged turbocharger thread, distorted converter connection or failed gasket. Correct those faults before reassembly.\u003c\/p\u003e\u003ch3\u003eInstallation and service notes\u003c\/h3\u003e\u003cp\u003eFollow the factory procedure for the exact turbocharger outlet arrangement. Allow the exhaust assembly to cool and support the connected exhaust component as prescribed before releasing the flange hardware.\u003c\/p\u003e\u003cp\u003eInspect the turbocharger flange threads, mating faces and stud positions. Remove damaged hardware using the appropriate repair procedure without damaging the threaded mounting hole. Do not install a new stud into compromised threads without completing the required repair.\u003c\/p\u003e\u003cp\u003eFit the correct stud in its assigned position using the prescribed installation method and thread preparation. Observe the specified installed position rather than applying an assumed universal insertion depth.\u003c\/p\u003e\u003cp\u003eUse the correct separate gasket and mating nut. Position the exhaust connection correctly and follow the prescribed tightening sequence, torque and any additional angle for that joint.\u003c\/p\u003e\u003cp\u003eDo not transfer a tightening value from the downpipe connection, another exhaust flange or an unrelated M10 fastener. Add lubricant, anti-seize or thread treatment only when the applicable factory procedure specifies it.\u003c\/p\u003e\u003cp\u003eComplete the required exhaust clearance and leak checks after assembly. Confirm that the connected exhaust is supported correctly and that every assigned flange position contains the proper hardware. This listing supplies one original stud; order the quantity needed for the repair.\u003c\/p\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A4\u003c\/td\u003e\n\u003ctd\u003e2009–2013\u003c\/td\u003e\n\u003ctd\u003e2.0L turbocharged gasoline, CAEB\u003c\/td\u003e\n\u003ctd\u003eB8\/B8.5 sedan, front-wheel drive; CVT\u003c\/td\u003e\n\u003ctd\u003eSpecified turbocharger outlet flange-to-catalytic converter stud. Match N10730201 and original flange arrangement; mating nut and sealing gasket are separate.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A4\u003c\/td\u003e\n\u003ctd\u003e2014–2016\u003c\/td\u003e\n\u003ctd\u003e2.0L turbocharged gasoline, CAED\u003c\/td\u003e\n\u003ctd\u003eB8.5 sedan, front-wheel drive; CVT\u003c\/td\u003e\n\u003ctd\u003eSpecified turbocharger outlet flange-to-catalytic converter stud. Match N10730201 and original flange arrangement; mating nut and sealing gasket are separate.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003e\u003cem\u003eConfirm the original stud number and turbocharger outlet flange arrangement before ordering. One stud supplied.\u003c\/em\u003e\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48007646609585,"sku":"N-107-302-01","price":5.15,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-107-302-01-genuine-vw-audi-1.jpg?v=1791297771","url":"https:\/\/hstuning.com\/products\/n-107-302-01-genuine-vw-audi-turbocharger-outlet-flange-stud","provider":"HS Tuning ","version":"1.0","type":"link"}