{"product_id":"n-107-480-01-genuine-vw-audi-6-x-16-thread-forming-torx-flange-bolt","title":"N-107-480-01 Genuine VW\/Audi 6 x 16 Thread-Forming Torx Flange Bolt","description":"\u003ch2\u003eCorrect thread-forming hardware for the original fastening point\u003c\/h2\u003e\u003cp\u003eN-107-480-01 is a Genuine VW\/Audi 6 x 16 thread-forming bolt with an internal Torx drive and a low rounded flange head. It replaces the specified original fastener in the oil-pan applications listed below.\u003c\/p\u003e\u003cp\u003eThe flange provides the intended head contact area while the thread-forming design differs from a conventional machine screw. Correct length, thread profile and head geometry matter when servicing the original pan; a similar-looking bolt is not sufficient identification.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eComplete factory number: N-107-480-01.\u003c\/li\u003e\n\u003cli\u003eFactory specification: 6 x 16 mm, thread-forming, internal hexalobular drive.\u003c\/li\u003e\n\u003cli\u003eDesign: Low rounded head with integral flange; match the original receiving hole and fastener specification.\u003c\/li\u003e\n\u003cli\u003eQuantity supplied: one individual bolt; pan, sealant and other fasteners are supplied separately.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe 6 x 16 designation identifies the nominal fastening size. It is not a packaged shipping dimension, and no unverified thread pitch or tightening torque is assigned.\u003c\/p\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRounded drive recess that prevents secure tool engagement during removal or installation.\u003c\/li\u003e\n\u003cli\u003eDamaged threads, a bent shank or an impaired head seating surface.\u003c\/li\u003e\n\u003cli\u003eMissing hardware or a previously installed substitute of the wrong length or thread form.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAn oil leak alone does not establish that the bolt is faulty. Inspect the pan flange, receiving threads and sealing joint before selecting the repair. A new fastener cannot restore a stripped receiving hole.\u003c\/p\u003e\u003ch3\u003eVehicle fitment\u003c\/h3\u003e\u003cp\u003eUse the table to match the vehicle, engine and transmission, then confirm that the original fastening point calls for this complete part number.\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eVolkswagen Jetta\u003c\/td\u003e\n\u003ctd\u003e2016–2018\u003c\/td\u003e\n\u003ctd\u003e1.4L turbocharged gasoline\u003c\/td\u003e\n\u003ctd\u003eMk6.5 sedan, FWD; 5-speed manual or automatic\u003c\/td\u003e\n\u003ctd\u003eOriginal lower oil-pan fastening locations specifying N-107-480-01; confirm original pan and hardware by VIN.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVolkswagen Jetta\u003c\/td\u003e\n\u003ctd\u003e2015\u003c\/td\u003e\n\u003ctd\u003e2.0L TDI diesel (CVCA)\u003c\/td\u003e\n\u003ctd\u003eMk6.5 sedan, FWD; 6-speed DSG\u003c\/td\u003e\n\u003ctd\u003eOriginal oil-pan fastener locations specifying N-107-480-01. Not an oil drain plug.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch3\u003eInstallation guidance\u003c\/h3\u003e\u003cp\u003eSupport and position the serviced component before starting the fastener. Use the correctly sized Torx tool, keep it fully seated, and follow the factory tightening sequence and torque for the exact pan and engine.\u003c\/p\u003e\u003cp\u003eDo not substitute a generic M6 machine screw, add thread-locking compound or reuse an unsuitable receiving thread without the repair procedure specifying it. Check the repaired joint and sealing area after service.\u003c\/p\u003e\u003ch3\u003eOrdering information\u003c\/h3\u003e\u003cp\u003eNew and unused inventory. Sold individually under complete factory number N-107-480-01. Order the quantity required for the repair after checking the original component and VIN.\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48049266360497,"sku":"N-107-480-01","price":0.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-107-480-01-genuine-vw-audi-1.jpg?v=1792157947","url":"https:\/\/hstuning.com\/products\/n-107-480-01-genuine-vw-audi-6-x-16-thread-forming-torx-flange-bolt","provider":"HS Tuning ","version":"1.0","type":"link"}