{"product_id":"n-903-086-07-genuine-vw-audi-clutch-pressure-plate-bolt-m8-x-14","title":"N-903-086-07 Genuine VW\/Audi Clutch Pressure Plate Bolt - M8 x 14","description":"\u003cp\u003e\u003cstrong\u003eGenuine VW\/Audi clutch pressure plate bolt, part number N-903-086-07.\u003c\/strong\u003e This original M8 x 14 shouldered socket-head fastener retains the clutch pressure plate at its assigned mounting position in the original clutch arrangement below. It is supplied individually for clutch service or replacement of damaged mounting hardware.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOriginal number: N-903-086-07 \/ N90308607.\u003c\/li\u003e\n\u003cli\u003ePublished nominal size: M8 x 14.\u003c\/li\u003e\n\u003cli\u003eInternal hex drive with a shouldered head arrangement.\u003c\/li\u003e\n\u003cli\u003eSpecified application: original clutch pressure plate mounting hardware.\u003c\/li\u003e\n\u003cli\u003eOne bolt supplied. Pressure plate, clutch disc, flywheel and other service hardware are separate.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe pressure plate mounting fasteners retain the cover assembly against the flywheel in its prescribed position. Correct hardware length and seating are necessary for the original mounting arrangement. This bolt is distinct from the larger fasteners that secure the flywheel to the crankshaft.\u003c\/p\u003e\u003cp\u003eMatch the original pressure plate and flywheel hardware before ordering. Replacement clutch kits and flywheel conversions can specify different fasteners, even on a vehicle with the same engine and transmission. This listing supplies one bolt rather than a complete pressure plate hardware set.\u003c\/p\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cp\u003eInspect these bolts when the clutch pressure plate is removed for clutch disc, flywheel or related service. Renew mounting hardware whenever the applicable factory or approved component procedure requires it.\u003c\/p\u003e\u003cp\u003eReplace damaged threads, a rounded internal hex drive, deformation, missing bolts or corrosion affecting installation. Earlier clutch work can leave incorrect substitute hardware or fasteners damaged by a poorly seated tool.\u003c\/p\u003e\u003cp\u003eInspect the pressure plate seating and flywheel threads along with the bolts. A new fastener cannot repair stripped flywheel threads, a distorted pressure plate, a worn clutch disc or a damaged flywheel surface.\u003c\/p\u003e\u003cp\u003eClutch slip, judder, release problems or noise require diagnosis of the complete clutch and release system. Replacing a mounting bolt alone does not correct worn friction material, contamination, flywheel damage or a failed release component. Repair the confirmed fault before reassembly.\u003c\/p\u003e\u003ch3\u003eInstallation and service notes\u003c\/h3\u003e\u003cp\u003eFollow the factory procedure for the original clutch arrangement and any instructions supplied with the approved replacement components. Confirm that the pressure plate, flywheel and prescribed bolt set are compatible before assembly.\u003c\/p\u003e\u003cp\u003eInspect the flywheel mounting threads and pressure plate contact surfaces. Position and align the clutch assembly as required, then start the correct bolts by hand without cross-threading. Keep friction surfaces free of contamination during the repair.\u003c\/p\u003e\u003cp\u003eUse a correctly sized internal hex tool fully seated in the drive. Follow the specified staged tightening sequence so the cover is drawn down evenly. Apply the prescribed torque and any additional angle for the exact pressure plate attachment.\u003c\/p\u003e\u003cp\u003eDo not transfer tightening requirements from flywheel-to-crankshaft bolts, a different pressure plate or another M8 fastener. Observe the specified thread preparation and replacement instructions. Do not use excessive force to compensate for an incompatible bolt or misaligned cover.\u003c\/p\u003e\u003cp\u003eIf the bolts do not seat normally, inspect hardware length, component compatibility and thread condition before continuing. Complete the required clutch release, transmission assembly and operating checks after the repair.\u003c\/p\u003e\u003cp\u003eThis listing supplies one original bolt. Obtain the full quantity and other required clutch hardware separately for the mounting arrangement being serviced.\u003c\/p\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eVolkswagen GTI 337\u003c\/td\u003e\n\u003ctd\u003e2002\u003c\/td\u003e\n\u003ctd\u003e1.8L turbocharged gasoline, AWP\u003c\/td\u003e\n\u003ctd\u003eMk4 hatchback, front-wheel drive, 337 edition; 6-speed manual\u003c\/td\u003e\n\u003ctd\u003eOriginal clutch pressure plate mounting arrangement requiring N90308607. Confirm original flywheel\/pressure plate hardware; aftermarket conversions can require different bolts.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVolkswagen GTI 20th Anniversary\u003c\/td\u003e\n\u003ctd\u003e2003\u003c\/td\u003e\n\u003ctd\u003e1.8L turbocharged gasoline, AWP\u003c\/td\u003e\n\u003ctd\u003eMk4 hatchback, front-wheel drive, 20th Anniversary edition; 6-speed manual\u003c\/td\u003e\n\u003ctd\u003eOriginal clutch pressure plate mounting arrangement requiring N90308607. Confirm original flywheel\/pressure plate hardware; aftermarket conversions can require different bolts.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003e\u003cem\u003eConfirm original N90308607 and the actual clutch\/flywheel arrangement before ordering. One bolt supplied.\u003c\/em\u003e\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48008260124849,"sku":"N-903-086-07","price":3.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-903-086-07-genuine-vw-audi-1.jpg?v=1791333444","url":"https:\/\/hstuning.com\/products\/n-903-086-07-genuine-vw-audi-clutch-pressure-plate-bolt-m8-x-14","provider":"HS Tuning ","version":"1.0","type":"link"}