{"product_id":"n-903-554-05-genuine-vw-audi-clutch-release-bearing-guide-sleeve-bolt","title":"N-903-554-05 Genuine VW\/Audi Clutch Release Bearing Guide Sleeve Bolt","description":"\u003cp\u003e\u003cstrong\u003eGenuine VW\/Audi clutch release bearing guide sleeve bolt, part number N-903-554-05.\u003c\/strong\u003e This original M7 x 14 fastener secures the separate throwout bearing guide sleeve to the transmission housing at its assigned position in the original clutch-release arrangement below. It is supplied individually for guide sleeve or related clutch service.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOriginal number: N-903-554-05 \/ N90355405.\u003c\/li\u003e\n\u003cli\u003ePublished nominal size: M7 x 14.\u003c\/li\u003e\n\u003cli\u003eInternal multi-point drive in the pictured socket head.\u003c\/li\u003e\n\u003cli\u003eSpecified application: release bearing guide sleeve-to-transmission housing attachment.\u003c\/li\u003e\n\u003cli\u003eOne bolt supplied. Guide sleeve, seals, release bearing and other clutch hardware are separate.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe guide sleeve provides the assigned sliding location for the release bearing in this clutch arrangement. Correct retaining hardware keeps the sleeve seated against the transmission housing. This bolt does not replace the guide sleeve itself or the separate pressure plate and flywheel fasteners.\u003c\/p\u003e\u003cp\u003eClutch-release arrangements differ across transmissions. Match the original number, actual gearbox and guide sleeve attachment before ordering. This listing supplies one fastener rather than a guide sleeve kit or complete clutch-release assembly.\u003c\/p\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cp\u003eInspect this bolt when the guide sleeve is removed during clutch or transmission service. Renew mounting hardware whenever the applicable factory or approved component procedure calls for replacement.\u003c\/p\u003e\u003cp\u003eReplace damaged threads, a worn internal drive, deformation, missing hardware or corrosion that prevents reliable installation. Earlier service may leave an incorrect substitute or a fastener damaged by an unsuitable drive tool.\u003c\/p\u003e\u003cp\u003eInspect the guide sleeve mounting face and transmission housing threads alongside the bolt. A new fastener cannot repair a worn sleeve surface, a damaged release bearing, a cracked mounting point or stripped housing threads.\u003c\/p\u003e\u003cp\u003eClutch release noise, rough operation or incomplete release requires diagnosis of the bearing, sleeve, fork and associated release components. Replacing the bolt alone does not correct those component faults. Repair the confirmed defect and restore the complete mounting arrangement.\u003c\/p\u003e\u003ch3\u003eInstallation and service notes\u003c\/h3\u003e\u003cp\u003eFollow the factory clutch-release and transmission procedure for the exact gearbox. Identify the separate guide sleeve and its prescribed mounting fasteners before assembly. Check the compatibility of any replacement guide sleeve with the original transmission.\u003c\/p\u003e\u003cp\u003eInspect the housing threads, sleeve contact face and related seals. Position the sleeve correctly and start the assigned bolt by hand without cross-threading. Do not use tightening force to pull a misaligned sleeve into position.\u003c\/p\u003e\u003cp\u003eUse the correctly sized drive tool fully engaged in the socket head. Follow the required tightening sequence and factory torque for the exact guide sleeve attachment, together with the specified thread preparation.\u003c\/p\u003e\u003cp\u003eDo not transfer a tightening value from the pressure plate, flywheel, slave cylinder or an unrelated M7 fastener. Follow the applicable hardware replacement requirements and the instructions for any approved replacement guide sleeve.\u003c\/p\u003e\u003cp\u003eIf the fastener does not seat normally, inspect sleeve alignment, bolt selection and thread condition before continuing. Correct damaged contact surfaces or housing threads before completing the connection.\u003c\/p\u003e\u003cp\u003eComplete the required clutch-release assembly and operating checks after service. Confirm the release components are correctly located and assembled before refitting the transmission. This listing supplies one original bolt; obtain the remaining guide sleeve and clutch hardware separately.\u003c\/p\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\u003ctr\u003e\n\u003ctd\u003eVolkswagen GTI 1.8T\u003c\/td\u003e\n\u003ctd\u003e2004–2005\u003c\/td\u003e\n\u003ctd\u003e1.8L turbocharged gasoline, AWP\u003c\/td\u003e\n\u003ctd\u003eMk4 hatchback, front-wheel drive; 5-speed manual\u003c\/td\u003e\n\u003ctd\u003eOriginal separate clutch release bearing guide sleeve-to-transmission housing position requiring N90355405. Match actual guide sleeve and transmission; other clutch-release arrangements differ.\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003e\u003cem\u003eConfirm original N90355405 and the actual guide sleeve\/transmission arrangement before ordering. One bolt supplied.\u003c\/em\u003e\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48008279490737,"sku":"N-903-554-05","price":3.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-903-554-05-genuine-vw-audi-1.jpg?v=1791333773","url":"https:\/\/hstuning.com\/products\/n-903-554-05-genuine-vw-audi-clutch-release-bearing-guide-sleeve-bolt","provider":"HS Tuning ","version":"1.0","type":"link"}