{"product_id":"n-906-484-02-genuine-vw-audi-rear-upper-shock-mount-bolt-m10-x-1-5-x-35","title":"N-906-484-02 Genuine VW\/Audi Rear Upper Shock Mount Bolt - M10 x 1.5 x 35","description":"\u003cp\u003e\u003cstrong\u003eGenuine VW\/Audi rear upper shock mount bolt, part number N-906-484-02.\u003c\/strong\u003e This original M10 x 1.5 x 35 fastener secures the rear upper shock mount to the vehicle on the configurations below. The specified arrangement uses two bolts per side; this listing supplies one bolt.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOriginal number: N-906-484-02 \/ N90648402.\u003c\/li\u003e\n\u003cli\u003ePublished nominal size: M10 x 1.5 x 35.\u003c\/li\u003e\n\u003cli\u003eExternal hex head with an attached washer.\u003c\/li\u003e\n\u003cli\u003eAssigned application: rear upper shock mount-to-vehicle attachment.\u003c\/li\u003e\n\u003cli\u003eOne bolt supplied. Shock absorber, upper mount and other mounting hardware are separate.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe rear upper mount connects the shock absorber assembly to the vehicle. Correct mounting hardware keeps the mount seated at its intended attachment points while the shock and mount perform their damping and isolation functions.\u003c\/p\u003e\u003cp\u003eThis fastener is for the assigned upper mount connection. It does not replace the lower shock bolt or the hardware securing the shock to the mount. Select each fastener by original number and attachment position rather than using one nominal thread size throughout the assembly.\u003c\/p\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cp\u003eInspect the bolts during rear shock or upper mount service. Replace missing hardware, damaged threads, rounded hex heads, deformation or corrosion that prevents reliable installation. Renew removed fasteners wherever the applicable factory procedure requires replacement hardware.\u003c\/p\u003e\u003cp\u003ePrevious work may leave unsuitable substitutes or an incomplete upper mount connection. Verify that both specified mounting positions on each serviced side have the correct hardware before completing the repair.\u003c\/p\u003e\u003cp\u003eRear suspension knocking, excessive body motion or an oil leak from the shock requires diagnosis of the shock, upper mount, bushings and related suspension components. A new bolt cannot restore a leaking damper, collapsed mount, cracked mounting component or damaged threaded vehicle attachment.\u003c\/p\u003e\u003ch3\u003eInstallation and service notes\u003c\/h3\u003e\u003cp\u003eFollow the factory rear shock and mount procedure for the exact vehicle. Support the vehicle and suspension at the prescribed points before removing the assembly. Use the specified method to control the shock and suspension position during service.\u003c\/p\u003e\u003cp\u003eInspect the upper mount, its seating surfaces and the mating vehicle threads. Position the mount correctly and start the bolts by hand in undamaged threads. Do not use the fasteners to force a misaligned mount against the body.\u003c\/p\u003e\u003cp\u003eUse the correct hex socket and follow the factory tightening sequence, torque and any additional angle for the upper mount-to-vehicle connection. Follow the specified thread preparation and hardware replacement instructions.\u003c\/p\u003e\u003cp\u003eDo not transfer a tightening value from the lower shock bolt, the shock rod nut or another M10 suspension attachment. Those connections can have different hardware and tightening requirements.\u003c\/p\u003e\u003cp\u003eIf a fastener does not seat normally, inspect the mount position, thread condition and bolt specification before proceeding. Excessive tightening does not repair a damaged attachment or compensate for an unsuitable bolt.\u003c\/p\u003e\u003cp\u003eAfter assembly, confirm all required mounting hardware is installed, the mount is seated and nearby components have the specified clearance. Complete the required suspension and operating checks after removing the supports.\u003c\/p\u003e\u003cp\u003eThis listing supplies one original bolt. Order the quantity required for the actual repair and select other shock and mount components separately.\u003c\/p\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\u003ctr\u003e\n\u003ctd\u003eVolkswagen GTI\u003c\/td\u003e\n\u003ctd\u003e2022–2024\u003c\/td\u003e\n\u003ctd\u003e2.0L turbocharged gasoline, EA888 Generation 4\u003c\/td\u003e\n\u003ctd\u003eMk8 hatchback, front-wheel drive; 7-speed DSG\u003c\/td\u003e\n\u003ctd\u003eRear upper shock mount-to-vehicle bolt. Two required per side; one supplied. Confirm N90648402 and factory rear mount arrangement. Not the lower shock attachment.\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003e\u003cem\u003eConfirm original N90648402 at the rear upper mount-to-vehicle connection before ordering. One bolt supplied.\u003c\/em\u003e\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48008297840817,"sku":"N-906-484-02","price":2.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-906-484-02-genuine-vw-audi-1.jpg?v=1791335083","url":"https:\/\/hstuning.com\/products\/n-906-484-02-genuine-vw-audi-rear-upper-shock-mount-bolt-m10-x-1-5-x-35","provider":"HS Tuning ","version":"1.0","type":"link"}