{"product_id":"n-908-123-02-genuine-vw-audi-blind-pop-rivet-6-x-10-mm","title":"N-908-123-02 Genuine VW\/Audi Blind Pop Rivet - 6 x 10 mm","description":"\u003ch2\u003eGenuine VW\/Audi Blind Pop Rivet\u003c\/h2\u003e\u003cp\u003eN-908-123-02 is an original blind rivet with a nominal 6 x 10 mm specification. It is used at assigned riveted fastening points, including selected bumper cover support and rear body\/package tray retainer locations. The rivet is installed from one side of the joint with an appropriate rivet-setting tool; pulling the mandrel forms the retaining end so the specified components are held together. One individual rivet is supplied.\u003c\/p\u003e\u003ch3\u003eTechnical details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOEM number:\u003c\/strong\u003e N-908-123-02 \/ N90812302.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNominal rivet size:\u003c\/strong\u003e 6 x 10 mm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eForm:\u003c\/strong\u003e Blind\/pop rivet with setting mandrel, as shown in the original photograph.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAssigned uses:\u003c\/strong\u003e Riveted component retention at the mounting positions identified in the original parts diagram.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eService:\u003c\/strong\u003e Install a new rivet after removing the old fastener; a set and drilled-out rivet cannot be reused.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupply:\u003c\/strong\u003e One rivet. Supports, shields, panels and the rivet-setting tool are separate.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCommon reasons to replace\u003c\/h3\u003e\u003cp\u003eNew rivets are needed when a riveted component is removed for repair or replacement. Missing hardware, a loose or incompletely set rivet, corrosion or damage around the joint can also require renewal. If the retained component has become loose, inspect its mounting holes and the underlying support for distortion, wear or cracking before installation. A correctly set rivet depends on the intended joint and hole condition; fitting new hardware will not repair an enlarged hole or a damaged mounting flange. Follow the original body repair instructions for any required repair to the attachment.\u003c\/p\u003e\u003ch3\u003eInstallation and service notes\u003c\/h3\u003e\u003cp\u003eConfirm the OEM number, rivet location and specified component stack before removing the old fastener. Protect nearby wiring, lines, trim and surfaces during drilling or removal, and remove debris from the area. Keep the original hole size and mounting arrangement intact; do not enlarge the hole to accommodate unrelated hardware. Align and support the parts, then use a suitable rivet-setting tool and the vehicle-specific installation procedure. Check that the rivet is fully seated and the retained component is secure. Do not substitute a screw, a different rivet length or an impact-bar mounting bolt for this assigned fastening point.\u003c\/p\u003e\u003ch3\u003eVehicle fitment\u003c\/h3\u003e\u003cp\u003eThe following confirmed profiles are restricted to the identified original riveted mounting point that specifies N90812302. A listed vehicle can use multiple rivet sizes, and this rivet is not a universal replacement for every body or support fastener.\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eVehicle\u003c\/th\u003e\n\u003cth\u003eModel years\u003c\/th\u003e\n\u003cth\u003eEngine\u003c\/th\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003cth\u003eApplication restrictions\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eVolkswagen Passat\u003c\/td\u003e\n\u003ctd\u003e2021\u003c\/td\u003e\n\u003ctd\u003e2.0L turbo gasoline\u003c\/td\u003e\n\u003ctd\u003eSE; sedan; Match original riveted mounting assembly\u003c\/td\u003e\n\u003ctd\u003eFront bumper cover cross-member\/support rivet, diagram position 16; not an impact-bar mounting bolt.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVolkswagen Passat\u003c\/td\u003e\n\u003ctd\u003e2022\u003c\/td\u003e\n\u003ctd\u003e2.0L turbo gasoline\u003c\/td\u003e\n\u003ctd\u003eSE \/ Limited Edition; sedan; Match original riveted mounting assembly\u003c\/td\u003e\n\u003ctd\u003eFront bumper cover cross-member\/support rivet, diagram position 16; not an impact-bar mounting bolt.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A6\u003c\/td\u003e\n\u003ctd\u003e2015\u003c\/td\u003e\n\u003ctd\u003e2.0L turbo gasoline\u003c\/td\u003e\n\u003ctd\u003ePremium Plus; C7 sedan; Match original riveted mounting assembly\u003c\/td\u003e\n\u003ctd\u003eRear body\/package tray retainer rivet, diagram position 8; match original riveted position.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A6\u003c\/td\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003e2.0L turbo gasoline\u003c\/td\u003e\n\u003ctd\u003ePremium; quattro; C7 sedan; Match original riveted mounting assembly\u003c\/td\u003e\n\u003ctd\u003eRear body\/package tray retainer rivet, diagram position 8; match original riveted position.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAudi A6\u003c\/td\u003e\n\u003ctd\u003e2018\u003c\/td\u003e\n\u003ctd\u003e3.0L supercharged gasoline V6\u003c\/td\u003e\n\u003ctd\u003ePremium; quattro; C7 sedan; Match original riveted mounting assembly\u003c\/td\u003e\n\u003ctd\u003eRear body\/package tray retainer rivet, diagram position 8; match original riveted position.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003e\u003cem\u003eConfirm N90812302, original rivet position and mounting arrangement by VIN before ordering.\u003c\/em\u003e\u003c\/p\u003e","brand":"Genuine VW\/Audi","offers":[{"title":"Default Title","offer_id":48012822249649,"sku":"N-908-123-02","price":0.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0681\/1379\/3201\/files\/n-908-123-02-genuine-vw-audi-1.jpg?v=1791515698","url":"https:\/\/hstuning.com\/products\/n-908-123-02-genuine-vw-audi-blind-pop-rivet-6-x-10-mm","provider":"HS Tuning ","version":"1.0","type":"link"}