OVERVIEW
Choose the forged piston set that matches your Audi EA839 3.0T build. Developed by 034Motorsport with JE Pistons, both options replace the factory pistons with a 2618 forged aluminum design and a nominal 10.0:1 compression ratio, compared with 11.2:1 stock.
Standard vs. Extreme
| Set | Part number | Best suited to | 034Motorsport design rating |
|---|---|---|---|
| Standard | 034-202-9107 | Stage 3 hybrid turbo builds such as TTE710, TTE810 or Pure750, especially when a full-frame turbo is not planned. | 200 hp per cylinder; intended for 1,200+ hp applications. |
| Extreme | 034-202-9111 | High-output hybrid turbo builds and projects planned around a larger full-frame turbo. | 300 hp per cylinder; intended for 1,800+ hp applications. |
These ratings describe the piston sets, not guaranteed engine or wheel horsepower. Engine output and durability depend on the complete build, fuel and calibration.
Technical Details
- Both sets use JE’s Forged Side Relief (FSR) construction. Its narrower skirts reduce cylinder-wall contact, and 034Motorsport says the design can weigh up to 20% less than conventional full-round forgings.
- Both use JE TUFF Skirt coating to reduce friction and wear, heavy-duty wrist pins, and JE Pro Seal rings.
- The lower nominal compression ratio gives a tuner more room to manage knock and ignition timing under boost. It does not replace a build-specific calibration.
What the Extreme Set Adds
- A stronger undercrown and reinforced wrist-pin towers, with 3D machining beneath the crown to control weight and balance.
- Extra-heavy-duty wrist pins with a 0.250-inch wall.
- Vertical and lateral gas ports that use combustion pressure to help seal the rings. The vertical ports are designed to resist carbon buildup, and accumulator grooves help stabilize pressure between the rings.
- JE Kool Kote hard anodizing on the piston surfaces and diamond-like carbon (DLC) coatings on the rings. The treatments are intended to help protect against heat, corrosion from aggressive racing fuels and material transfer between the rings and ring lands.
What’s Included
One matched set of six forged pistons in the selected configuration, with wrist pins and JE Pro Seal piston rings. The Extreme set uses DLC-coated rings. Connecting rods and other engine-build components are sold separately.
Fitment Sheet
| Vehicle | Starting year in 034’s guide | Chassis | Engine |
|---|---|---|---|
| Audi S4 | 2017 (market-dependent) | B9 / B9.5 only | EA839 3.0L turbocharged TFSI V6 |
| Audi S5 | 2018 | B9 / B9.5 only | EA839 3.0L turbocharged TFSI V6 |
| Audi SQ5 | 2018 | B9 / B9.5 only | EA839 3.0L turbocharged TFSI V6 |
The starting years are from 034Motorsport’s guide and may differ by market. Later years are covered only while the chassis and engine match. Confirm by VIN and engine code before ordering. The guide does not list the 2.9T, supercharged 3.0T, Q7/Q8 or later chassis.
Installation Guide
Professional installation by a qualified engine builder is recommended. Confirm the actual bore and cylinder finish, piston-to-wall clearance, ring end gaps and compatibility with the selected rods and pins before final assembly. Use the instructions and clearance specifications supplied with your exact piston set rather than assuming factory clearances apply. Forged pistons can be louder than the factory pistons on cold starts.
Download the JE 2618 installation tips (PDF).
Related Build Parts
These are separate upgrades, not required or included with the piston kit. Match hardware to your vehicle, turbo and calibration.
- Stage 3 acceleration package for B9/B9.5 Audi S4/S5 and TTE810 hybrid turbo specifications.
- Supertech valve springs and titanium retainers.
- 4-bar MAP sensors and high-pressure fuel pump piston upgrade.
- Optional billet oil-filter cap.
California Proposition 65
Warning: This product may expose you to chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. See P65Warnings.ca.gov.
