OVERVIEW
Genuine VW/Audi 079-129-717-B seals the joint between the lower intake manifold and the cylinder head on the applications listed below. Correct sealing at this joint keeps intake air within its intended path and helps maintain consistent engine operation.
Technical details
- Original equipment part number: 079-129-717-B.
- Application position: lower manifold-to-cylinder-head intake port seal.
- Sold individually. The listed supercharged V6 applications use six port seals at this sealing level; this listing supplies one gasket.
- The upper and lower intake gaskets occupy different joints. Match the full part number and sealing position before ordering.
- Photographs showing multiple seals are reference images; they do not change the quantity supplied.
Common reasons to replace
Replace a seal that is cut, torn, flattened, hardened or distorted, or one that no longer seats evenly in its groove. Renew the applicable seals when the workshop procedure requires replacement after disassembly. On supercharged 3.0T engines, work on components underneath the supercharger may expose these intake joints; the required gasket selection depends on which assemblies are removed.
Leakage at an intake joint can contribute to unstable idle, mixture-correction faults and poor drivability. These symptoms can also result from other faults, so inspect and test the intake system before selecting parts. A damaged gasket cannot correct a cracked housing, a distorted sealing surface or an unrelated fuel or ignition problem.
Installation and service notes
Clean the mating surfaces and inspect the gasket groove without allowing debris into the intake ports. Confirm that the seal fits its intended recess, lies evenly and is not rolled or pinched as the assembly is lowered into place. Follow the application-specific fastening sequence and torque values; confirm any additional seals, fasteners and service requirements in the workshop procedure.
For the supercharged V6 applications, inspect the complete set of six seals at the disturbed joint. Removing the lower manifold exposes the cylinder-head intake ports; protect those openings throughout the repair. The manifold, supercharger and other repair components are not included.
Fitment
| Vehicle | Model years | Engine | Configuration | Application restrictions |
|---|---|---|---|---|
| Audi A6 | 2009–2011 | 3.0T TFSI (CCAA) | ; Not specified by source | Engine code must match; verify VIN and installed intake manifold sealing arrangement |
| Audi S4 | 2010–2012 | 3.0T TFSI (CCBA) | ; Not specified by source | Engine code must match; verify VIN and installed intake manifold sealing arrangement |
| Audi S5 | 2010–2012 | 3.0T TFSI (CCBA) | Cabriolet; Not specified by source | Engine code must match; verify VIN and installed intake manifold sealing arrangement |
| Audi A6 | 2012 | 3.0T TFSI (CGXB) | ; Not specified by source | Engine code must match; verify VIN and installed intake manifold sealing arrangement |
| Audi A7 | 2012 | 3.0T TFSI (CGXB) | ; Not specified by source | Engine code must match; verify VIN and installed intake manifold sealing arrangement |
| Audi Q7 | 2011–2012 | 3.0T TFSI (CJWB / CJWC / CJWE) | ; Not specified by source | Engine code must match; verify VIN and installed intake manifold sealing arrangement |
| Audi A6 | 2013–2014 | 3.0T TFSI | ; Not specified by source | 3.0L supercharged gasoline engine; verify VIN and installed intake manifold sealing arrangement |
| Audi A7 | 2013–2014 | 3.0T TFSI | ; Not specified by source | 3.0L supercharged gasoline engine; verify VIN and installed intake manifold sealing arrangement |
| Audi S4 | 2013–2014 | 3.0T TFSI | ; Not specified by source | 3.0L supercharged gasoline engine; verify VIN and installed intake manifold sealing arrangement |
| Audi S5 Coupe | 2013–2014 | 3.0T TFSI | ; Not specified by source | 3.0L supercharged gasoline engine; verify VIN and installed intake manifold sealing arrangement |
| Audi S5 Cabriolet | 2013–2014 | 3.0T TFSI | ; Not specified by source | 3.0L supercharged gasoline engine; verify VIN and installed intake manifold sealing arrangement |
| Audi Q5 | 2013–2014 | 3.0T TFSI | ; Not specified by source | 3.0L supercharged gasoline engine; verify VIN and installed intake manifold sealing arrangement |
| Audi Q7 | 2013–2014 | 3.0T TFSI | ; Not specified by source | 3.0L supercharged gasoline engine; verify VIN and installed intake manifold sealing arrangement |
| Audi SQ5 | 2014–2017 | 3.0L supercharged TFSI V6 | B8 / B8.5 quattro; Automatic | Supercharged gasoline engine only; excludes later turbocharged SQ5. Confirm lower manifold-to-cylinder-head sealing location by VIN. |
| Volkswagen Touareg | 2011–2015 | 3.0L supercharged gasoline V6 / electric hybrid | Hybrid; 7P; Automatic | Hybrid only; excludes TDI diesel and 3.6L VR6. Lower intake manifold-to-cylinder-head seal; verify VIN. |
Confirm the complete part number, VIN, engine and sealing location before ordering. Body style and engine restrictions in the table apply.
