OVERVIEW
Genuine VW/Audi Threaded Sealing Plug
N-106-379-01 is an original threaded closure plug with an M12 x 1.5 x 12 specification. It closes an assigned threaded opening in the original assembly. Confirmed applications include the retainer/sealing plug in selected 1.8L Volkswagen turbocharger assemblies and designated drain-plug locations in the Audi R8 lower oil pan/tube assembly. The role and sealing arrangement depend on the exact installation; use the part number and diagram position to identify the correct opening. The listed RS3 application uses this plug at its assigned closure point in the seven-speed dual-clutch transmission assembly. One individual plug is supplied.
Technical details
- OEM number: N-106-379-01 / N10637901.
- Nominal specification: M12 x 1.5 x 12.
- Form: Threaded plug with an internal drive recess and integral seating flange, as shown in the original photograph.
- Assigned use: Closure of the original threaded opening specified for this part.
- Supply: One plug. Separate seals, oil pan, turbocharger and retained components are not included.
Common reasons to replace
Replacement may be appropriate when the internal drive is rounded, threads are damaged, the seating face is scored or corrosion prevents correct removal and installation. A missing plug or a plug renewed during assembly service also requires the correct replacement. If leakage is present, first identify its source and inspect the plug seat, mating threads and any required separate seal. A new plug cannot repair stripped housing threads or a cracked casting. Fluid appearing near a plug can also originate from a nearby tube, gasket or connection, so confirm the cause before replacing parts.
Installation and service notes
Identify the exact assembly and original plug number by VIN. Allow the assembly to cool and follow its service procedure for access, fluid handling, sealing hardware and tightening. Use the correct internal-drive tool fully seated in the recess. Inspect the threaded opening and seating face, start the plug without cross-threading, and install any separately specified seal according to the repair instructions. Do not assume every M12 plug is interchangeable or infer a tightening value from thread size alone. After service, restore fluid levels where applicable and check the serviced area for leakage. For the Volkswagen profiles below, use the turbocharger retainer plug position; for the listed R8 profiles, use the identified lower oil pan/tube drain location.
For the RS3 transmission application, identify the diagram-specified opening before removal and follow the gearbox-specific procedure for fluid handling, sealing and tightening. Replace the plug if its drive recess, threads or sealing face are damaged. A new closure plug does not correct an internal mechatronics fault; leakage requires inspection of the separate seal and housing as well.
Vehicle fitment
These confirmed profiles require the original assembly and mounting position specifying N10637901. Engine displacement alone does not establish compatibility with every plug on the vehicle.
| Vehicle | Model years | Engine | Configuration | Application restrictions |
|---|---|---|---|---|
| Volkswagen Jetta | 2014 | 1.8L turbo gasoline | SE; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Jetta | 2015 | 1.8L turbo gasoline | SE / Sport; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Jetta | 2016 | 1.8L turbo gasoline | SEL Premium; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Jetta | 2017 | 1.8L turbo gasoline | Sport; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Jetta | 2018 | 1.8L turbo gasoline | Sport / SE Sport / SEL; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Passat | 2014 | 1.8L turbo gasoline | SE; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Passat | 2015 | 1.8L turbo gasoline | Sport; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Passat | 2016 | 1.8L turbo gasoline | S / SE / SEL / SEL Premium; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Volkswagen Passat | 2017 | 1.8L turbo gasoline | S; sedan; Match original assembly and plug position | Turbocharger assembly retainer/sealing plug, diagram position 21; 1.8L application only. |
| Audi R8 | 2008 | 4.2L gasoline V8 | Base; Type 42 coupe; Match original assembly and plug position | Lower oil pan/tube assembly drain plug at the position specifying N10637901; match original sealing hardware. |
| Audi R8 | 2010 | 4.2L gasoline V8 | Base; Type 42 coupe; Match original assembly and plug position | Lower oil pan/tube assembly drain plug at the position specifying N10637901; match original sealing hardware. |
| Audi R8 | 2014 | 4.2L gasoline V8 | Spyder; Type 42; Match original assembly and plug position | Lower oil pan/tube assembly drain plug at the position specifying N10637901; match original sealing hardware. |
| Audi RS3 | 2019 | 2.5L turbo gasoline | 8V sedan; quattro; 7-speed S tronic / DQ500 | Threaded closure plug in the DSG mechatronics/transmission assembly, diagram position 46; match the original N10637901 plug and separate specified sealing hardware. Not a blanket engine-oil drain-plug application. |
Confirm N10637901, original plug location and required separate sealing hardware by VIN before ordering.
